Welcome to the Australian Ford Forums forum.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact us.

Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated.

Go Back   Australian Ford Forums > Club and Speciality Forums > Forum Community Car Clubs > AU Falcon.com.au

Reply
 
Thread Tools Display Modes
Old 01-04-2018, 05:05 PM   #1
Vortex-98
Regular Member
 
Vortex-98's Avatar
 
Join Date: Nov 2016
Posts: 205
Default AU Tickford 4into1 vs stock xr8 extractors

Just wondering which of these 2 would give most performance to a v8 being the tickford has press bends an the xr8 mini mandrel bends (not sure of pipe size) an because catylitic converters are attached which has a better cat in terms of flow an quality
__________________
[B]WTB (Syd)...AU 5.0 or xr8 4 speed auto transmission in good working cond /B]
Vortex-98 is offline   Reply With Quote Multi-Quote with this Post
Old 01-04-2018, 07:54 PM   #2
XC50077
Drive'n Cruise'n Live'n
 
XC50077's Avatar
 
Join Date: May 2013
Location: Western Sydney
Posts: 916
Default Re: AU Tickford 4into1 vs stock xr8 extractors

AFAIK, XR8 Tickford are the same ,the only difference I know of is the AUXR8 220kw have better flowing cat converters and no heat shields. Cheers.
XC50077 is offline   Reply With Quote Multi-Quote with this Post
Old 02-04-2018, 12:24 PM   #3
au350hp
FF.Com.Au Hardcore
 
Join Date: Jun 2017
Posts: 1,341
Default Re: AU Tickford 4into1 vs stock xr8 extractors

Quote:
Originally Posted by Vortex-98 View Post
Just wondering which of these 2 would give most performance to a v8 being the tickford has press bends an the xr8 mini mandrel bends (not sure of pipe size) an because catylitic converters are attached which has a better cat in terms of flow an quality
I have a stock 220kw AU & have been researching best exhaust systems for the street. These recommendations are based on stock internals & a system that takes advantage of the low end torque & sounds tough. Pacemaker or Advance will both do the job, stock cats are fine & use a Manta 3'' single OR have a dual 2&1/4'' system made. As many have pointed out to me, dyno tuning is done at wide open throttle which doesn't happen much with street driving, so be aware of 'Race Proven' and words like that. I have decided on ceramic coated Advance headers, a single 3'' system with some decent mufflers. I may or may not use after market cats as I don't think there is any real gains for a stock motor. Good luck. The answer to your question is neither. One may give a few HP more at some point but they will be so close it doesn't matter.
au350hp is offline   Reply With Quote Multi-Quote with this Post
Old 04-04-2018, 06:14 PM   #4
Vortex-98
Regular Member
 
Vortex-98's Avatar
 
Join Date: Nov 2016
Posts: 205
Default Re: AU Tickford 4into1 vs stock xr8 extractors

The tickford 4 into 1 pipes are crimped up near the flange the stock xr8 design I thought would flow better down low an have better catylitic converters
__________________
[B]WTB (Syd)...AU 5.0 or xr8 4 speed auto transmission in good working cond /B]
Vortex-98 is offline   Reply With Quote Multi-Quote with this Post
Old 04-04-2018, 07:35 PM   #5
boss351290
FF.Com.Au Hardcore
 
Join Date: Jun 2012
Posts: 1,017
Default Re: AU Tickford 4into1 vs stock xr8 extractors

There the same. The t-series engines had ceramic coating which make them look like stainless steel and the 220kw and 250kw engines had 1.8 litre cats all other engines had 1.3 litre cats.
boss351290 is offline   Reply With Quote Multi-Quote with this Post
Old 06-04-2018, 03:27 PM   #6
au350hp
FF.Com.Au Hardcore
 
Join Date: Jun 2017
Posts: 1,341
Default Re: AU Tickford 4into1 vs stock xr8 extractors

I have decided on a set of Advance headers which I'm getting coated in a grey colour to help look stock, I will keep the cats most likely, and buy the Manta 3'' single. I will post when done.
au350hp is offline   Reply With Quote Multi-Quote with this Post
Old 13-04-2018, 01:57 AM   #7
Vortex-98
Regular Member
 
Vortex-98's Avatar
 
Join Date: Nov 2016
Posts: 205
Default Re: AU Tickford 4into1 vs stock xr8 extractors

What does the difference in cats off the 220 an 250kw mean in flow are they more hi flow or same just bit bigger ..if never heard them described in litres...so the are quite a bit bigger with a 5 litre diffrence
__________________
[B]WTB (Syd)...AU 5.0 or xr8 4 speed auto transmission in good working cond /B]
Vortex-98 is offline   Reply With Quote Multi-Quote with this Post
Reply

Thread Tools
Display Modes

Forum Jump


All times are GMT +11. The time now is 08:36 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Other than what is legally copyrighted by the respective owners, this site is copyright www.fordforums.com.au
Positive SSL