|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
01-02-2008, 07:00 PM
|
#1 | ||
|
Starter Motor
Join Date: Jan 2008
Posts: 3
|
Hi all, great forum with heaps of helpful info.
Down to my issue, just got my TX5 back from the mechanic and it is running really bad after 1/2 an hour. I would like to look at the engine fault codes. Plenty of info out there for the 626/Probes but I can't find where to connect for the Telstar TX5's. Any help would be greatly appreciated. The engine is running like it is only firing two cyclinders when it gets a good heat soak through the engine bay. At cold and short trips round town it is running OK. But I do long trips for work and don't want to get stuck anywhere. Lucky it started playing up about 5km from home and limped home. Cheers, Quattro. |
||
|
|
|
01-02-2008, 08:10 PM
|
#2 | ||
|
Over Thinker
Join Date: Dec 2005
Location: Ipswich Qld
Posts: 1,351
|
for questions about TX5 made after 87 please try www.telstarperformance.co.nr
http://z3.invisionfree.com/tx5/index.php?
__________________
My car goes Brumm Brumm |
||
|
|
|
|
01-02-2008, 08:50 PM
|
#3 | ||
|
Starter Motor
Join Date: Jan 2008
Posts: 3
|
Thanks but they haven't got any service manuals or much info in any of the forum topics or posts. Any more ideas. Have tried pdftown and a few other location.
|
||
|
|
|
|
03-02-2008, 06:32 AM
|
#4 | ||
|
Over Thinker
Join Date: Dec 2005
Location: Ipswich Qld
Posts: 1,351
|
looking for you
__________________
My car goes Brumm Brumm Last edited by dirty hands; 03-02-2008 at 06:40 AM. |
||
|
|
|
|
03-02-2008, 06:37 AM
|
#5 | ||
|
Over Thinker
Join Date: Dec 2005
Location: Ipswich Qld
Posts: 1,351
|
http://www.autobookworld.com/shopexd.asp?id=2793
1991 ford telsar repair manual so heat is the issue effecting the electronics dont know your model so this is a guess if coil plugs, dissy cap, and leads have been replaced replace the engine management computer - get one from a wrecker till you get one that works electronically the fault codes read the following sensors ecu /dissy module / the air flow meter/ the throttle position sensor/02 sensor as the common listings you can buy an LED tester from dick smiths
__________________
My car goes Brumm Brumm |
||
|
|
|
|
03-02-2008, 09:41 AM
|
#6 | ||
|
Starter Motor
Join Date: Jan 2008
Posts: 3
|
Thank for you comments Dirty Hands. Car goes back to the mechanics tomorrow, but I wanted to check to fault codes before it went back to make sure he was being honest. Cheers.
|
||
|
|
|
1991 Telstar TX5 Ghia Engine Codes
Hybrid Mode