|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
02-09-2005, 05:53 PM
|
#1 | ||
|
Nat D
Join Date: Jul 2005
Posts: 1,131
|
hi does anyone know if its possible to take the au rear tail lights out easily? what do i have to do just so i have the tail light cover? as i want to lightly tint it?
|
||
|
|
|
02-09-2005, 05:57 PM
|
#2 | ||
|
Nat D
Join Date: Jul 2005
Posts: 1,131
|
or if any one has tinted rear lights, can you please tell me how you did it while they are on the car?
|
||
|
|
|
|
02-09-2005, 06:31 PM
|
#3 | ||
|
Nat D
Join Date: Jul 2005
Posts: 1,131
|
has anyone got any info at all about tinting any tail lights? should i just mask around edges with tape..
cheers |
||
|
|
|
|
02-09-2005, 06:52 PM
|
#4 | ||
|
Boost Addict
Join Date: Jan 2005
Location: North Brisbane
Posts: 1,151
|
illegal
|
||
|
|
|
|
02-09-2005, 08:39 PM
|
#5 | ||
|
Miami Pilot
 
Join Date: Jan 2005
Location: ACT
Posts: 21,703
|
A couple of light coats should be OK. As long as the red and amber can still be seen, you'll be OK.
To remove the taillights: 1. Open boot. 2. Undo 2 screws holding light in 3. From inside boot, undo plastic clip and loosen the boot lining covering the back part of the taillight 4. Undo the 10mm nut 5. Pull the tail light out. 6. Installation is the reverse of removal As for actually removing the lens from the body of the taillight - there is no known method for doing this (unlike the headlights), as the whole light assembly is plastic welded.
__________________
-----------------------------------------------------------------
The Hammer: FG GTE | 376rwkw | 1/4 mile 11.793 @ 119.75mph 1.733 60' (4408lb) 1 of 60 FG MK1 335 GTEs (1 of 118 FG Mk 1 & 2 335 GTEs). Mods: Tune, HSD/ShockWorks, black GT335 19” staggered replicas with 245 & 275/35/19 Michelin Pilot sport 5s Daily: BF2 Fairmont Ghia I6 ZF, machine face GT335 19” staggered Replicas with 245s and 275s, Bilsteins & Kings FPV 335 build stats: <click here> Ford Performance Club ACT |
||
|
|
|
|
03-09-2005, 10:12 AM
|
#6 | |||
|
Nat D
Join Date: Jul 2005
Posts: 1,131
|
Quote:
cheers |
|||
|
|
|
|
02-09-2005, 09:40 PM
|
#7 | ||
|
Boost Addict
Join Date: Jan 2005
Location: North Brisbane
Posts: 1,151
|
there is a way of removing the plastic lense from the assembly
it is basically uruthaned together, basically chuck it in the oven around 50 to 80 degree for a few minutes and then start pulling it apart. keep heating it up until they seperated. there are little clips all around it that hold both parts together as well. in order to rejoin them use uruthane, regular silican can be too agressive and damage the plastic. i have also used liquid nails on commodore lighst before because it was cheaper 
|
||
|
|
|
|
03-09-2005, 10:19 AM
|
#8 | ||
|
Boost Addict
Join Date: Jan 2005
Location: North Brisbane
Posts: 1,151
|
for the carpet? just keep pulling
|
||
|
|
|
|
03-09-2005, 12:01 PM
|
#9 | ||
|
Barra Turbo > V8
  
Join Date: Jan 2005
Posts: 25,978
|
had to replace a tail light globe today i have every spanner except the 100mm to get light out god damn it AU's i have discovered are a pain in the rear to replace any globe compared to my old ED
__________________
-2011 XR6 Turbo Ute - Lux Pack - M6 -2022 Hyundai Tucson Highlander Diesel N Line |
||
|
|
|
tail light removal
Hybrid Mode