|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|
Thread Tools | Display Modes |
|
02-01-2012, 11:28 PM | #1 | ||
QUEENSLANDER!
Join Date: Jan 2012
Location: Brisbane
Posts: 38
|
How do I replace a thermostat in a 1998 Falcon Futara (auto) ?
|
||
03-01-2012, 09:40 AM | #2 | ||
FF.Com.Au Hardcore
Join Date: Jun 2005
Posts: 588
|
There's a thermostat housing near the front passenger side of the engine, with a large radiator hose coming out of it, plus a smaller hose and pipe.
Undo the two bolts and put the top aside, pull out the old thermostat, put the new one in along with a new gasket. If you have a torque wrench, the setting for the bolts is 20Nm. HTH. |
||
03-01-2012, 10:28 AM | #3 | ||
rexnet
Join Date: Feb 2010
Location: Adelaide, South Australia
Posts: 3,562
|
its an idea to pay attention to the torque setting. i snapped a head off one of the bolts once. can i just say that sucked balls.
|
||
This user likes this post: |
03-01-2012, 04:28 PM | #4 | ||
Regular Member
Join Date: Oct 2008
Location: Burpengary, Q
Posts: 112
|
But please firstly remove the radiator expansion tank cap (slowly) so there is no chance of any pressure buildup in the cooling system.
When removing those two bolts, ease them undone evenly. By that I mean undo each one a little alternately, until they are both finger tight, to remove by hand. DON'T remove one completely before loosening the other! Good luck.... |
||
03-01-2012, 08:47 PM | #5 | ||
FF.Com.Au Hardcore
Join Date: Jun 2005
Posts: 588
|
I've removed my thermo housing cover maybe 5 times over the past 7 years, I just undid both bolts?? I also didn't use a torque wrench, so they're probably done up a lot tighter than they should be. I ended up using a bit of form-a-gasket around the edge to seal a minor leak (which may have been because of the overtightened bolts)
Maybe I'm just lucky nothing bad has happened. I should have mentioned in my first post that the engine (and therefore coolant) should be stone cold. Apologies for missing that. |
||
03-01-2012, 09:00 PM | #6 | ||
FF.Com.Au Hardcore
Join Date: Jan 2005
Posts: 767
|
Can I ask why it should be stone cold? I've done a few on falcons and its never been cold, in fact its been quite warm.
__________________
______________________________________ 2006 BF MKII Winter White Wagon |
||
03-01-2012, 09:06 PM | #7 | ||
FF.Com.Au Hardcore
Join Date: Jun 2005
Posts: 588
|
Stone cold to be safe... but generally just not pressurised.
|
||
04-01-2012, 01:40 AM | #8 | ||
rexnet
Join Date: Feb 2010
Location: Adelaide, South Australia
Posts: 3,562
|
I always use a bit of permitex on the thermostat gasket. Just to help it seal nice
|
||
This user likes this post: |
07-02-2014, 09:37 AM | #9 | ||
Starter Motor
Join Date: Jan 2014
Location: Tauranga, New Zealand
Posts: 10
|
Read a post that mentioned removing small hose from header tank and draining some of the coolant before undoing housing, so coolant doesn't spill out over motor I presume. Is this right?
|
||