|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
07-01-2011, 06:30 PM
|
#1 | ||
|
Regular Member
Join Date: Jan 2005
Posts: 42
|
Hi, changed the oil recently on my AU1 4.0l. I noticed a small leak from the sump plug so bought a fibre washer and put it on, but the washer broke (I wasn't really twisting that hard either).
Anyway, as I was trying to temporarily put the bolt back in, it wouldn't go all the way in and I noticed some metal spring poking out of the hole. Probably a helicoil that mechanic had put in in a previous service. I've put the bolt back in but not all the way. Not sure what to do now, because I wouldn't have a clue how to remove the old helicoil and perhaps replace it. Would it be an expensive job for a mechanic? I have searched, but most threads relate to fixing a stripped thread. Would be grateful for any suggestions. |
||
|
|
|
07-01-2011, 06:38 PM
|
#2 | |||
|
Falcon Unbelievable!
Join Date: Jul 2005
Location: Uncle Henry's Garage
Posts: 382
|
Quote:
Biggest tip that I was given was to tighten the plug first to break the vacuum then loosen it off. Comes off nice and easy after that. Good luck amigo |
|||
|
|
|
|
07-01-2011, 11:11 PM
|
#3 | ||
|
When in doubt, GAS IT!!
Join Date: Sep 2006
Location: Lower Eyre Peninsula, SA
Posts: 3,018
|
__________________
. HERS- BFIII Wagon Gold, alloys, dual fuel, bullbar, big tow pack, trans cooler, fully rebuilt HD suspension, Clarion, alarmed, full 2 1/2" sports system, mint body MINE- AUII Forte Meteorite, dual fuel but otherwise bog stock. MINE- AUII Fairlane Sportsman Liquid Silver over meteorite,HIDs', Airhog, Eagle Leads, dual fuel, custom rear springs, BA slotted discs + a second one for spares . |
||
|
|
|
|
14-02-2015, 07:29 PM
|
#4 | ||
|
Starter Motor
Join Date: May 2014
Posts: 2
|
cost me $240 my mechanic got a mobile thread repair bloke in he did it without undoing the engine mounts somehow
|
||
|
|
|
|
14-02-2015, 07:32 PM
|
#5 | ||
|
Starter Motor
Join Date: May 2014
Posts: 2
|
cost me $240 for a mobile thread repair bloke to come and do it he put a new helicoil in but it still seeps oil
|
||
|
|
|
|
15-02-2015, 02:55 PM
|
#6 | ||
|
XR6T BA 2002
Join Date: Apr 2011
Posts: 683
|
I bought a sump 12mm sump plug bolt that tappers out to 12.8mm
used 2 sump plug washers originals they strip pretty easy you only meant to tighten them to 15nm as per the workshop manual
__________________
XR6T 2002 BA
|
||
|
|
|
|
15-02-2015, 04:06 PM
|
#7 | ||
|
Guest
Join Date: May 2013
Posts: 1,934
|
Maybe try some Loctite aviation gasket sealant no:3. (The non hardening one)
Put some of that on the thread & around the O ring seal / washer, hopefully that'll stop any leaks. |
||
|
|
|
|
15-02-2015, 10:21 PM
|
#8 | ||
|
FF.Com.Au Hardcore
Join Date: Feb 2005
Location: Melb north
Posts: 12,025
|
or you can go to ford and get a no. 1 or no. 2 or no. 3 over size sump plug and a tap dependent on what you need and do the job that way.
|
||
|
|
|
|
17-02-2015, 12:31 PM
|
#9 | ||
|
Banned
Join Date: Mar 2010
Location: PERTH. WA
Posts: 4,697
|
I use a plastic washer and thread tape on mine,never leaks.
|
||
|
|
|
AU sump plug
Hybrid Mode