|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
20-03-2016, 11:02 AM
|
#1 | ||
|
Irregular member
Join Date: Dec 2004
Location: Melbourne
Posts: 3,941
|
After spending two hours removing the ECU's security bolt, I am now confused as to how to remove the wiring loom through the firewall hole. Do I pull it into the cabin or into the engine bay?
Either way, the round firewall hole looks too small for the ECU and dash plug (which end up at the hole at the same time!) or the engine connector (a big square block). Any help is much appreciated...
__________________
2000 AU II FAIRLANE 75th ANNIVERSARY - big and shiny My hovercraft is full of eels! Movie Car Chase of the Week: Gene Hackman driving a 1971 Pontiac LeMans to chase an elevated train in The French Connection (1971). |
||
|
|
|
20-03-2016, 11:05 AM
|
#2 | ||
|
RIP...
Join Date: Dec 2004
Posts: 15,524
|
I think I did mine all from the engine bay.
2 people make it much easier, 1 pulling and the other pushing.
__________________
. Oval Everywhere... |
||
|
|
|
|
20-03-2016, 05:10 PM
|
#3 | ||
|
RIP...
Join Date: Dec 2004
Posts: 15,524
|
That didn't help you much did it...
The ECU plug is what goes through the hole.
__________________
. Oval Everywhere... |
||
|
|
|
|
20-03-2016, 05:50 PM
|
#4 | ||
|
Irregular member
Join Date: Dec 2004
Location: Melbourne
Posts: 3,941
|
Thanks mate, I will give it a try and will let you know, haven't been able to have a look at it today. The white dash plug (if that's what it is) tends to bunch up with the ECU plug at the same time so it makes it double tricky.
__________________
2000 AU II FAIRLANE 75th ANNIVERSARY - big and shiny My hovercraft is full of eels! Movie Car Chase of the Week: Gene Hackman driving a 1971 Pontiac LeMans to chase an elevated train in The French Connection (1971). |
||
|
|
|
|
21-03-2016, 02:37 PM
|
#5 | ||
|
Donating Member
 Join Date: Nov 2011
Location: Melbourne
Posts: 4,573
|
It is tricky, but yes definitely pulled through from engine bay.
|
||
|
|
|
|
26-03-2016, 10:10 PM
|
#6 | ||
|
Irregular member
Join Date: Dec 2004
Location: Melbourne
Posts: 3,941
|
With sliced up fingers, I have finally done it! It turned out that there was a cable running through the hole with a brown plug in behind the dash which I undid so I could make more room to pass it through.
There was also a couple of green vacuum lines (I think) bundled together which ran right through where it all passes through to come out, so the loom gets hung on it several times due to clips and things which protrude from it.
__________________
2000 AU II FAIRLANE 75th ANNIVERSARY - big and shiny My hovercraft is full of eels! Movie Car Chase of the Week: Gene Hackman driving a 1971 Pontiac LeMans to chase an elevated train in The French Connection (1971). |
||
|
|
|
| This user likes this post: |
V8 ECU wiring loop removal help
Hybrid Mode