|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
08-03-2008, 09:24 AM
|
#1 | ||
|
Starter Motor
Join Date: Feb 2008
Posts: 8
|
Dumb question re: where to place the e-tag. There is a "mesh" area on the windscreen. Should the etag be placed in this area or below it.
Thanks |
||
|
|
|
08-03-2008, 09:59 AM
|
#2 | ||
|
v8+9in=FUN!!!!!
Join Date: Feb 2008
Location: sydney
Posts: 54
|
doesnt really matter
__________________
:MrT_anim: : |
||
|
|
|
|
08-03-2008, 03:10 PM
|
#3 | ||
|
FF.Com.Au Hardcore
Join Date: Jan 2007
Location: Melbourne northern suburbs
Posts: 4,025
|
mine is on the mesh, works fine
|
||
|
|
|
|
08-03-2008, 04:27 PM
|
#4 | ||
|
Motorsport Guru
Join Date: Jan 2005
Location: The Blue Mountains, N.S.W.
Posts: 1,680
|
I was driving a Hire Car to Queensland Raceway and had my N.S.W. E-Tag in my pocket and to my surprise it worked fine. If it's going in the Mondeo there should be plenty of room just below where the Rear View Mirrow is attached to the windscreen. You shouldn't be able to see it from there too.
__________________
Interior Enhancements: Footwell Lighting, Brushed Alum. H/brake Handle, 6 Disc In-Dash System. Exterior Enhancements: ST170 Wheels, Richbrook Shorty Aerial, Euro-Spec Hatch Handle. Performance Enhancements: Ate Callipers/EBC Rotors/EBC Greens Stuff Pads, ST170 Suspension, Herrod's Custom Tune, Ford Racing Coated Exhaust Manifold & Bespoke 2.25in Exhaust. Awards: AFD '07 EFOC Best Focus, SFS '09 EFOC Best Focus, SFS '10 RSOC O/all Best Focus, AFD '10 CFC O/all Best Focus. |
||
|
|
|
|
09-03-2008, 05:02 PM
|
#5 | ||
|
Giddy up!
Join Date: Dec 2007
Location: Melbourne
Posts: 2,126
|
My holder is literally just below the last line of dots. Did the same thing in my Falcon, works fine. And if you're like me and needed to replace a work one form your own, I wrote 'work' on theirs and could easily make it out in the reflection, so I would take it off and use mine. Easy.
|
||
|
|
|
|
10-03-2008, 12:16 PM
|
#6 | ||
|
Starter Motor
Join Date: Oct 2005
Posts: 14
|
I've spray painted mine matt black along with the bracket, then you dont notice it from outside either. They have just brought out newer smaller ones from Citylink that are easier to remove from the bracket too...
|
||
|
|
|
E-Tag Placement
Linear Mode
