|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
| OzECruisers General Discussions E/N/D vehicles General Discussion ONLY. NO TECH THREADS |
 |
|
|
Thread Tools | Display Modes |
22-01-2005, 02:39 AM
|
#1 | ||
|
FF.Com.Au Hardcore
Join Date: Dec 2004
Posts: 696
|
Hey guys, i just bought a lip spoiler.
Its black in colour and has lots of scratches in it so its off to get repainted. It will be cheaper if i prepare the spoiler and then send it off to be painted. I was wondering how u prepare the spoiler? Sand it back with sandpaper? WHat sorta sandpaper??... stuff like that.. In regards to installing the thing, I notice it has a couple of screws, so i need to drill the boot itself.. Has anyone done this? can you give me a few pointers.. thanks
__________________
4.0Lturbo T56 AP Racing 520rwhp |
||
|
|
|
22-01-2005, 10:41 AM
|
#2 | ||
|
E-Series Owners Club
Join Date: Dec 2004
Location: Sth. East. Suburbs, Melbourne
Posts: 781
|
Unless the paint is cracked, it's easiest to sand it back a little, rather than right back to rubber (as it will then have to be re-primed). Just use some wet-and-dry sandpaper, if the scratches are deep, use some 400 or so and then finish it with some 800. If the scrathces are really fine, then just use the 800.
As for drilling the boot, line the spoiler up in the right spot, and mark where you need to drill. Check where the holes are going to be so that they aren't going to hit something on the other side (when they go through). If they are, put some hose or some kind of spacer on the drill bit to stop it from going through too far. You may find it easier if you drill a small hole or use a centre punch first to stop the drill from moving around, too. |
||
|
|
|
|
22-01-2005, 12:47 PM
|
#3 | ||
|
Banned
Join Date: Dec 2004
Location: South East Melbourne
Posts: 6,156
|
Take the clear cloat off, DON'T sand it back to rubber.
|
||
|
|
|
|
22-01-2005, 03:47 PM
|
#4 | ||
|
Last warning
Join Date: Dec 2004
Location: Mornington Peninsula, Victoria HeadCount: 3
Posts: 11,194
|
nothing wrong with taking it back to rubber if it needs it, aslong as u prime it properly :o
__________________
FALCN6 - Turbo, Air Bag Suspension - Hibernating EL GT - Supercharged NASCAR - 83 Thunderbird , Bagged DAILY - BA Fairlane Ghia, Boss 260 Turbo OFFROADER - Ford Explorer 
|
||
|
|
|
|
22-01-2005, 04:42 PM
|
#5 | ||
|
FF.Com.Au Hardcore
Join Date: Dec 2004
Posts: 696
|
thanks guys... spesh thanatos lots a help
__________________
4.0Lturbo T56 AP Racing 520rwhp |
||
|
|
|
|
22-01-2005, 05:17 PM
|
#6 | |||
|
Banned
Join Date: Dec 2004
Location: South East Melbourne
Posts: 6,156
|
Quote:
|
|||
|
|
|
|
22-01-2005, 05:23 PM
|
#7 | ||
|
Banned
Join Date: Jan 2005
Location: Keilor, Vic
Posts: 1,498
|
I sanded mine back not to rubber though. Sprayed it in high fill and rubbed it back. Now time for a primer coat and then a couple a coats of Pearl Green 2pac and the a clear coat and done!
|
||
|
|
|
Preparing Boot lip spoiler and installing it.
Linear Mode
