|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
25-01-2012, 12:56 AM
|
#1 | ||
|
[AUT-747]
Join Date: May 2010
Posts: 595
|
hey guys,
my rear bumper on the left hand side where it meets the rear quarter panel is not sitting flush anymore, there is a little gap between the quarter and the bumper and i can see the rivets in between the gap. my question is how can i fix it or adjust it so it sits without the gap? if it helps too it was caused when i had a little bit of a tight squeeze in the garage and pushed the bumper in on that side. cheers. |
||
|
|
|
25-01-2012, 10:37 AM
|
#2 | ||
|
Next upgraded Mk1 Leopard
 
Join Date: Jan 2005
Location: Sydney, in the burbs
Posts: 4,913
 
|
Take it of, get some washers and space out the difference.
UK
__________________
Plastic Surgery 1 AUII Monsoon Blue How 2's: Change rear view mirror, Install backfire valve, Change foam front seats, Install auto transmission cooler, Replace Trans Shift Globe, Remove front door Trim, Paint AU headlights, install door spears, Premium Rear Parcel Shelf, go here...
 |
||
|
|
|
|
26-01-2012, 10:17 PM
|
#3 | ||
|
[AUT-747]
Join Date: May 2010
Posts: 595
|
stupid question. what do you mean by space by the difference ?
cheers |
||
|
|
|
|
27-01-2012, 02:37 PM
|
#4 | ||
|
Banned
Join Date: Dec 2007
Posts: 3,290
|
He means put some washers on the bar the nut attaches to on back bumper behind the rear wheels to push the bumper back out to sit flush with ur car
|
||
|
|
|
|
27-01-2012, 02:39 PM
|
#5 | ||
|
Banned
Join Date: Dec 2007
Posts: 3,290
|
Or if it's the other two bolts in the boot I found Undoing them getting someone else to push the bumper up to where u want it then doing the nuts up super tight works sometimes and keeps it in place
|
||
|
|
|
|
27-01-2012, 09:30 PM
|
#6 | ||
|
Next upgraded Mk1 Leopard
Join Date: Jan 2005
Location: Sydney, in the burbs
Posts: 4,913
|
Yeap, thats what I ment.
 UK
__________________
Plastic Surgery 1 AUII Monsoon Blue How 2's: Change rear view mirror, Install backfire valve, Change foam front seats, Install auto transmission cooler, Replace Trans Shift Globe, Remove front door Trim, Paint AU headlights, install door spears, Premium Rear Parcel Shelf, go here...
|
||
|
|
|
|
30-01-2012, 01:10 AM
|
#7 | ||
|
[AUT-747]
Join Date: May 2010
Posts: 595
|
i think you're right on the money for pushing it up and tightening the bolts, thats probably my best bet. ill let you know how it goes.
cheers |
||
|
|
|
AU falcon rear bumper problem
Linear Mode
