|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
26-08-2013, 09:14 PM
|
#1 | ||
|
Regular Member
Join Date: Aug 2005
Posts: 139
|
got the car back from the mechanics today. and was told that my front calipers may be buggered. the inner brake pads are about 85% worn while the outers are only about 50% worn. so he suspects the calipers are sticking.
so what are my options? new/reco calipers or rebuild the calipers? then there is also the au2/3/ba/bf front brake upgrade, although there does seem to be a bit involved there. and i guess its a bit of a gamble using parts from a wreckers etc. i would probably want to go with new pads and rotors which ups the cost abit. |
||
|
|
|
26-08-2013, 09:21 PM
|
#2 | ||
|
Donating Member
 
Join Date: Aug 2005
Location: St John's Park NSW
Posts: 1,454
|
I would check the Slides and see if they are working properly. Calipers rarely get buggered so easily as they are cast.
How dirty is the brake fluid? how long has it been since your car had a brake flush? You are right about the AU2,3, BA, BF brake upgrade. It requires you to change the lower control arms, stub axles, brake hoses, sway bar and add 2 sway bar brackets. Just check what I mentioned first ok? the slides can get pretty dirty and can cause your trouble as well. |
||
|
|
|
|
26-08-2013, 09:37 PM
|
#3 | ||
|
Regular Member
Join Date: Aug 2005
Posts: 139
|
righto, ill give the slides a look.
i know up for new pads, rotors have minor shudder so due for a machine soon but i might just upgrade to slotted rotors and some good pads. Fluid was done 10,000 ago (i think) 20,000 at most. Will have to check how it looks. Cheers. |
||
|
|
|
|
20-09-2013, 12:02 PM
|
#4 | ||
|
Regular Member
Join Date: Aug 2005
Posts: 139
|
have just got new bendix general ct pads and rda slotted and dimple drilled rotors, ready to go on.
i'm thinking i should remove the calipers and replace all the seals and rubbers, for roughly $50 for the kit, its probably worthwhile to just do it now. when i remove the banjo bolt disconnecting the brake line from the caliper, brake fluid is obviously going to leak out, how much is going to leak out while i have the calipers off? is it just going to be a bit of what is in the line? or is it going to keep going until the reservoir is empty? |
||
|
|
|
|
20-09-2013, 12:13 PM
|
#5 | ||
|
Guest
Join Date: Feb 2007
Location: Gods Country
Posts: 16,258
|
It will gravity feed untill the master cyl is empty not advisable,you can buy plastic clamps that crimp onto the rubber brake hose to stop this...
|
||
|
|
|
|
20-09-2013, 04:23 PM
|
#6 | ||
|
Regular Member
Join Date: Aug 2005
Posts: 139
|
i have a set of clamps like these vvvv that i have used to clamp diesel fuel lines on my navara when changing fuel filters.
ill give these a go. i was just a bit sceptical of using them on brake lines. http://www.ebay.com.au/itm/CLAMPS-FO...40968c0&_uhb=1 |
||
|
|
|
| This user likes this post: |
|
20-09-2013, 06:46 PM
|
#7 | ||
|
Guest
Join Date: Feb 2007
Location: Gods Country
Posts: 16,258
|
Exactly the type i use matey, cost me $15 from Repco
But mine are yellow 
|
||
|
|
|
|
21-09-2013, 01:18 PM
|
#8 | ||
|
Regular Member
Join Date: Aug 2005
Posts: 139
|
awesome mate, thanks for the help.
|
||
|
|
|
series 1 front brake calipers
Linear Mode
