|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-12-2009, 06:46 PM
|
#61 | ||
|
FF.Com.Au Hardcore
Join Date: Apr 2009
Location: jimboomba
Posts: 4,638
|
also i guess ill be up for another wheel alingment as well
__________________
Welder/Fabricator at Beaudesert Exhuast Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors |
||
|
|
|
07-12-2009, 08:17 PM
|
#62 | ||
|
FF.Com.Au Hardcore
Join Date: Apr 2009
Location: jimboomba
Posts: 4,638
|
i was getting sick of the noise today, so me and my grandfather pulled my wheel off and found that the mech who put my camber caster kit on never tightend up the top arm and it was causing it to knock, so i tightend the arm up today and no more knocking, also when they put my wheel back on they stripped one of my studs,
thank god for that, my orignal ball joints live on to die another day
__________________
Welder/Fabricator at Beaudesert Exhuast Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors |
||
|
|
|
|
07-12-2009, 08:24 PM
|
#63 | ||
|
Just slidin'
Join Date: Sep 2005
Location: Brisvegas
Posts: 7,791
|
New suspension will come loose usually within a day or two of installation, its happened to me twice. Just retighten everything after a good drive and it should be right.
__________________
MD Mondeo - For the family
NP Pajero - For the adventure |
||
|
|
|
|
07-12-2009, 08:27 PM
|
#64 | ||
|
FF.Com.Au Hardcore
Join Date: Apr 2009
Location: jimboomba
Posts: 4,638
|
all good now anyways, what beats me is they did the wheel alingment like that,
anyways saved my self some money, car is booked in for a free check over on wednesday anyways to make sure, different place as well
__________________
Welder/Fabricator at Beaudesert Exhuast Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors |
||
|
|
|
|
22-12-2013, 12:36 PM
|
#65 | ||
|
Guest
Join Date: Feb 2012
Location: Sydney
Posts: 653
|
Do you know if fluid comes out when the rack switch is taken off to change over?
|
||
|
|
|
|
22-12-2013, 04:22 PM
|
#66 | |||
|
FF.Com.Au Hardcore
Join Date: Aug 2006
Location: Salamander Bay
Posts: 5,427
|
Quote:
__________________
[SIGPIC][/SIGPIC]
Everyone starts off with a bag full of luck and an empty bag of experience. The trick is to fill the experience bag before the luck bag is empty. "It is better to remain silent and be thought a fool than to speak out and remove all doubt." Start a new career as a bus driver Rides: FG2 XR6 stock at this stage but a very nice ride xc 4 DOOR X CHASER 5.8 UNDER RESTO |
|||
|
|
|
Linear Mode
