|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|
Thread Tools | Display Modes |
27-09-2009, 01:07 PM | #1 | ||
Regular Member
Join Date: Aug 2005
Posts: 139
|
My rear view mirror is losely mounted to the wind screen, wasnt mounted properly a few years back when I had a windscreen replaced.
It rattles and vibrates over bumps etc. Can anyone give me instructions on how to remove and re-fit properly? |
||
27-09-2009, 01:32 PM | #2 | ||
FF.Com.Au Hardcore
Join Date: Apr 2009
Location: jimboomba
Posts: 4,638
|
your going to have to reglue it back on to the windscreen, dont just pull it off, if you do it will crack the windscreen, i think they are just glued on by memory,
just get some fishing line and put it behind it and cut it with the line off clean it up and just reglue it back on
__________________
Welder/Fabricator at Beaudesert Exhuast Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors |
||
28-09-2009, 08:47 AM | #3 | |||
gone fishing
Join Date: Jul 2006
Location: Morayfield qld
Posts: 286
|
Quote:
cheers
__________________
Cheers Whiskers |
|||
28-09-2009, 10:01 AM | #4 | ||
Banned
Join Date: Dec 2004
Location: searching for cubes
Posts: 6,672
|
There are two parts - the metal base which is glued to the screen and the mirror mount which slides over the base. The mount has a metal spring clip arrangement in it and is probably where your problem lies. Pull the mirror off and try to reshape the metal clip in whatever direction is needed so as to apply more pressure when it is replaced.
|
||
28-09-2009, 06:01 PM | #5 | |||
Regular Member
Join Date: Aug 2005
Posts: 139
|
Quote:
Had a bit of a go but it wasnt coming off and I didnt want to pull it too hard and damage it. |
|||
28-09-2009, 06:11 PM | #6 | ||
FF.Com.Au Hardcore
Join Date: Apr 2009
Location: jimboomba
Posts: 4,638
|
if you pull it off it will probaly break the glass, if its glued, just get some fishin line and feen it through the glue to cut it off
__________________
Welder/Fabricator at Beaudesert Exhuast Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors |
||
28-09-2009, 08:55 PM | #7 | |||
Banned
Join Date: Dec 2004
Location: searching for cubes
Posts: 6,672
|
Quote:
Get your head up under the fixture and you will see how it comes off. |
|||
29-09-2009, 09:22 PM | #8 | |||
Regular Member
Join Date: Aug 2005
Posts: 139
|
Quote:
The metal base thats on the windscreen is solid as a rock. So the problem is either where it mounts on to the base, or where the metal clip on the mirror joins to the actual mirror its a bit loose which i think might be causeing it or maybe its a bit of both. Maybe I should just get a new mirror to clip on to the windscreen? |
|||
29-09-2009, 09:38 PM | #9 | ||
Banned
Join Date: Dec 2004
Location: searching for cubes
Posts: 6,672
|
The metal clip is riveted to the mirror base - get a helper to hold the base on a piece of softwood (like pine) while you try a hammer and pin punch to tighten the rivet. Bit risky but at worst you are still up for a new mirror whichever way you go. And if it works you're laffin'.
|
||
30-09-2009, 06:54 AM | #10 | ||
Walking with God
Join Date: Mar 2005
Location: Melbourne
Posts: 7,321
|
The S1 mirrors are held to the bracket by a small allen key bolt. A far more sensible setup than the spring clip T3man has described. IIRC this setup is leftover from the E series. For S2, they switched setups - cheaper I guess?
I had the same problem on my S2 SR and ended up getting another mirror from the wreckers, as it was nigh on impossible to get the spring reshaped. All the best with it. GK
__________________
2009 Mondeo Zetec TDCi - Moondust Silver 2015 Kia Sorento Platinum - Snow White Pearl 2001 Ducati Monster 900Sie - Red Now gone! 1999 AU1 Futura Wagon - Sparkling Burgundy On LPG Want a Full Life? John 10:10 |
||
30-09-2009, 07:00 PM | #11 | ||
Regular Member
Join Date: Aug 2005
Posts: 139
|
Where's the best place to pick up a new mirror? Does it have to be a ford mirror to fit the base or are they universal?
|
||
28-10-2013, 04:43 PM | #12 | ||
Starter Motor
Join Date: Oct 2013
Posts: 1
|
I just removed mine easily on my 2001 ford falcon xr8 au ll with the spring clip. On YouTube look up how to remove a rear vision mirror on a ford falcon au ll by John Wilson. He has a specific tool to do the job and I made my own out of wood reinforced with blue tape once it fit. Came off super easy in seconds with the tool after struggling with a screw driver etc for longer than I care to say.
|
||
This user likes this post: |
06-08-2022, 10:04 AM | #13 | ||
Donating Member
Join Date: Jan 2007
Posts: 292
|
For future reference for anybody who get here like the way I did.
All new OEM replacement mirrors for AU to FG come with T20 screw head; may require tightening if it rattles. |
||