Hard to get bits Wanted or For Sale

[dj5800]

I am after a tailshaft for my coupe, 351, C4 to 9".
I have a tailshaft from a sedan but it does not suit the 9" uni. apparently i can change the yoke in the 9".
If anyone has either part please let me know.
Located near sydney.

[Tha Jack]

Hey Guys,

Im on the hunt for a Right Hand Rear Quater Panel for a coupe.
Any one know where I can get one?
(I know they are rare as rocking horse poop)

Cheers Jack

[ThaFlash]

edit:
tha jack, a person i know used the front guard off a sedan as a rear 1/4.

i am not sure which coupe you are referring to but it was done with an XB Coupe front guard and put on the back.

[XA-MONT]

I think you are slightly mistaken HP4ME, the front wheel arches can be used to rebuild the rear wheel arches on a coupe, but if he wants an entire rear quarter panel i am assuming there is more damage than just the wheel arches.

[ThaFlash]

thanks XA-MONT that's sounds more like what I was getting at.

Though a good portion of the sedan front guard was used on mine length wise and including (what I call) the lateral line.

[XB GS 351 Coupe]

Originally Posted by dj5800

I am after a tailshaft for my coupe, 351, C4 to 9".
I have a tailshaft from a sedan but it does not suit the 9" uni. apparently i can change the yoke in the 9".
If anyone has either part please let me know.
Located near sydney.

First you will need to work out what size uni you have on the tail shaft and what size yoke you have on the 9"...there are really only two main sizes used on the 9" in Australia.

1310 and 1330.

1330 being the bigger one, also refered to by some people as GTHO Yoke.

So you will have either one of those. All you need to do is buy the correct uni for you application and fit it to the tailshaft and you are done, you either buy 1310 to 1310 (if you have small yoke and tail shaft) or 1330 to 1330 (if you have large tail shaft and yoke) and the one you probably need 1310 to 1330 which will convert one size to the other.

Cheaper than a new tail shaft or new yoke.

[dj5800]

Originally Posted by XB GS 351 Coupe

First you will need to work out what size uni you have on the tail shaft and what size yoke you have on the 9"...there are really only two main sizes used on the 9" in Australia.

1310 and 1330.

1330 being the bigger one, also refered to by some people as GTHO Yoke.

So you will have either one of those. All you need to do is buy the correct uni for you application and fit it to the tailshaft and you are done, you either buy 1310 to 1310 (if you have small yoke and tail shaft) or 1330 to 1330 (if you have large tail shaft and yoke) and the one you probably need 1310 to 1330 which will convert one size to the other.

Cheaper than a new tail shaft or new yoke.

yeah, thanks for that, have spoken with Pieter from http://www.mrtshafts.com.au/ContactUs.htm he has been great and is sending me a 'cross uni' as you have described above.

[Tha Jack]

Originally Posted by Tha Jack

Hey Guys,

Im on the hunt for a Right Hand Rear Quater Panel for a coupe.
Any one know where I can get one?
(I know they are rare as rocking horse poop)

Cheers Jack

Just found out that new repo ones will be available in november next year .
unfortunately I cant wait that long
I may be able to use the front half of a ute side panel.

[buggerlugs]

Jack , on my XCcoupe we used a front right guard for the rear left guard and vice versa. I had rust issues around the arches..........

[Tha Jack]

The main part I need is the half section that is from the middle of the wheel arch towards the drivers door.
Thanks Guys

[Geez Louise]

To clear up a bit of confusion, the section below is what we are looking for. This section needs to be replaced on my coupe and the rebuild is on hold until I can find a replacement panel.



It has been repaired there previously and the metal is really thin.

Cheers
Coll

[buggerlugs]

Oh, ok. I have only ever seen one on E-Bay and they were asking $1500 for it.........

[greenjgs]

Hi All

I'm looking for a RH B Pillar Skin from a Coupe, PV or Ute if anyone has one.

Cheers Graeme

[THE4RD]

Originally Posted by Geez Louise

To clear up a bit of confusion, the section below is what we are looking for. This section needs to be replaced on my coupe and the rebuild is on hold until I can find a replacement panel.



It has been repaired there previously and the metal is really thin.

Cheers
Coll

Give Tin West a call. They could probably make one up using the original panel as a template.

http://www.yellowpages.com.au/vic/we...0-listing.html

[memphis2k]

Originally Posted by greenjgs

Hi All

I'm looking for a RH B Pillar Skin from a Coupe, PV or Ute if anyone has one.

Cheers Graeme

I will be wrecking a ute that is relatively rust free next week, drop me a PM.

[greenjgs]

PM sent thanks

[danthefordman]

Originally Posted by memphis2k

I will be wrecking a ute that is relatively rust free next week, drop me a PM.

Dont suppose you have the chrome trim off the windscreen by any chance. Need the top piece specifically. They do fit a coupe don't they?


Also chasing honeycomb trim off the back below the boot lid if any one has any.

Cheers

Dan

[Coupes and More]

Originally Posted by danthefordman

Dont suppose you have the chrome trim off the windscreen by any chance. Need the top piece specifically. They do fit a coupe don't they?


Also chasing honeycomb trim off the back below the boot lid if any one has any.

Cheers

Dan

you will find the top piece of windscreen chrome is coupe only and none you find will fit, they will to short but if you get 2 sedan bits of trim cut them and join the abit like the bottom piece it should do ok

[danthefordman]

Originally Posted by Coupes and More

you will find the top piece of windscreen chrome is coupe only and none you find will fit, they will to short but if you get 2 sedan bits of trim cut them and join the abit like the bottom piece it should do ok

I know the sedan trim doesn't work as is, couple inches too narrow but are you saying the ute is too short as well. I assumed since the doors on utes are the same for coupes and vans (different glass i know) that the roof line was also the same. We tried with a sedan piece but the curves are different as well so it is a little more difficult than just a cut and shut. Looks bodgy too.

[King Neptune]

I was of the opinion that utes were the same as coupes, but utes are definately the same as p/vans, & from memory the pv screens are sedan. I'm happy to be corrected, but I'm pretty sure.
Cheers Rob.

[JG65TE]

yup coupe is coupe, sedan,panno,wagon and ute are all the same.

[gcg2503]

Hey Guys
Chasing the following parts for my Landau
1. Landau Emblem suitable for rechroming (no pitting etc)
2. Landau rear vinyl roof moulds (or just the large passenger side piece as the rest are fine)
3. Front and Rear Overriders
4. Bonnet hinges/springs - mine are a little tired and want a better set

[zeuss000]

Hi Folks, i am chasing a front spoiler / air dam? and rear moulded type spoiler to suit an XC. i am in Brisbane area but don't mind paying shipping,
Cheers
Ed

[GT-GTF]

Hi All - I'm chasing a driver's side xb coupe door.

[dj5800]

after power steering bracket which bolts to the block for the tear drop shaped power steering pump.

[CJR09]

guys chasing xa gt/gs dash fascia - no instrumentation just fascia

also xa 302c 550 wide radiator/fan shroud

cheers

[GT-GTF]

Im also after a second hand rear window rubber pls!

[darkside]

looking for interior light wiring and rear pillar courtasy lights and wiring that plugs into rear loom ,the things that dissapear in rebuilds ...doc

[GT-GTF]

I have found an old rubber from one of my old restos so I will reuse it.

I am still chasing a driver's door (xb).

[BTTB]

Originally Posted by zeuss000

Hi Folks, i am chasing a front spoiler / air dam? and rear moulded type spoiler to suit an XC. i am in Brisbane area but don't mind paying shipping,
Cheers
Ed

If you mean the "Cobra Style" front and rear spoilers...
they are readily available from numerous Aftermarket Suppliers

One of the site sponsers might even have them

eBay too
http://cgi.ebay.com.au/XC-FRONT-SPOI...item27b867429d