![]() |
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
Shockworks Ford damper specialist located in Melbourne's S.E suburbs. Website Link |
![]() |
|
Thread Tools | Display Modes |
![]() |
#61 | ||
Regular Member
Join Date: Jan 2013
Posts: 304
|
Hi, Benno
With the ute clearance, you can usually get to the top mount easily to adjust the damper with no problem. Cheers |
||
![]() |
![]() ![]() |
![]() |
#62 | ||
Call me dirt... Joe Dirt
Join Date: May 2009
Location: Back in Perth for good
Posts: 5,302
|
Ah, so the rear dampers are internally adjustable?
You need to take off the top mount bolt and turn the body of the damper in order to adjust? Thanks. Joe.
__________________
2007 BFII FPV Cobra Ute|Boss 302|6M|#23/100 Mods so far: Billet Products Shifter|X-Force Exhaust|Herrod Oil Breathers|Whiteline Sway Bar|Tein SuperStreets|Kings FOR-303SL Rear Springs|Melling Oil Pump|Mace Manifold Spacers|Powerbond Underdrives|Pacemaker Headers|Ballistic Cats|XFT Custom Tune @ 308.3rwkw|DBA T3 Rotors|Ferodo Pads|Goodridge Braided Lines Mods to come: 4.11 Diff Gears|Chromoly Tailshaft I use & recommend: Castrol|Motorcraft|Mainlube|Penrite Check Out My Build Thread |
||
![]() |
![]() ![]() |
![]() |
#63 | ||
Regular Member
Join Date: Jan 2013
Posts: 304
|
Ha Ha They are not Koni's mate!! We have an adjuster knob under the top mount that you can just turn to make the damping force change so takes about 3 seconds a damper. No need to remove or unbolt, can be played with when installed.
Cheers |
||
![]() |
![]() ![]() |
This user likes this post: |
![]() |
#64 | |||
Call me dirt... Joe Dirt
Join Date: May 2009
Location: Back in Perth for good
Posts: 5,302
|
Quote:
I thought that was it, but I couldn't make it out from the photos of the damper. So who could I approach to get these set up in WA? Joe.
__________________
2007 BFII FPV Cobra Ute|Boss 302|6M|#23/100 Mods so far: Billet Products Shifter|X-Force Exhaust|Herrod Oil Breathers|Whiteline Sway Bar|Tein SuperStreets|Kings FOR-303SL Rear Springs|Melling Oil Pump|Mace Manifold Spacers|Powerbond Underdrives|Pacemaker Headers|Ballistic Cats|XFT Custom Tune @ 308.3rwkw|DBA T3 Rotors|Ferodo Pads|Goodridge Braided Lines Mods to come: 4.11 Diff Gears|Chromoly Tailshaft I use & recommend: Castrol|Motorcraft|Mainlube|Penrite Check Out My Build Thread |
|||
![]() |
![]() ![]() |
![]() |
#65 | ||
Regular Member
Join Date: Jan 2013
Posts: 304
|
We have not had the chance to talk to any dealers yet in WA, but takes about ten minutes to fit to the rear and off you go.
if you know any good reputable places we should contact, let us know. All our time currently is in development and tuning lately so need to find some good people in the states other than Vic. The dampers are $699 for the pair and are fully rebuildable at a cost of $80 each and have a 12 months warranty which includes any track use. They are a big bore montubes, proven to be very robust and tuned for some serious bumpy roads we have in Australia. Cheers |
||
![]() |
![]() ![]() |
![]() |
#66 | |||
Join Date: Jul 2005
Location: Perth, Western Australia
Posts: 4,513
|
Quote:
.
__________________
2015 FGX XR8 5.0 S/C 645 RWKW ![]() |
|||
![]() |
![]() ![]() |
This user likes this post: |
![]() |
#67 | ||
Call me dirt... Joe Dirt
Join Date: May 2009
Location: Back in Perth for good
Posts: 5,302
|
Brett,
I reckon you should give Peter at Wilkinson Suspension Centre a call. He's a pretty reputable fitter and is very involved in the local racing scene and sponsors a few of the local car clubs, including the FPV Tickford owners club of WA, of which I'm a member too. Joe.
__________________
2007 BFII FPV Cobra Ute|Boss 302|6M|#23/100 Mods so far: Billet Products Shifter|X-Force Exhaust|Herrod Oil Breathers|Whiteline Sway Bar|Tein SuperStreets|Kings FOR-303SL Rear Springs|Melling Oil Pump|Mace Manifold Spacers|Powerbond Underdrives|Pacemaker Headers|Ballistic Cats|XFT Custom Tune @ 308.3rwkw|DBA T3 Rotors|Ferodo Pads|Goodridge Braided Lines Mods to come: 4.11 Diff Gears|Chromoly Tailshaft I use & recommend: Castrol|Motorcraft|Mainlube|Penrite Check Out My Build Thread |
||
![]() |
![]() ![]() |
2 users like this post: |
![]() |
#68 | ||
BOSS 5.4L Enthusiast
Join Date: Aug 2005
Posts: 21,904
|
Shockworks do you have a list of workshops using you gear in Victoria or nation wide for that matter?
|
||
![]() |
![]() ![]() |
![]() |
#69 | ||
Regular Member
Join Date: Jan 2013
Posts: 304
|
Hi FPV8U,
At this time, we have been doing the Ford installs as as we are new to the market have limited dealers in Victoria still. Also busy in Korea tuning race and road cars for our partners. Our current dealers are Import Monster and Forced motor works for the Japanese range and Wheeltech in Dandenong that sell all the range and have a good fitting service. Apart from that we need to get interstate to make new friends haha. Many people order from interstate and fit themselves but really need to increase our dealer range for us to keep growing. I have been a chassis engineer for many years but still learning all about what it takes to run and increase the sales side of things. Travelling overseas so much doesn't help but the money is great to put into the development costs so we can keep building the range. Any idea's are always welcome!! ![]() Cheers |
||
![]() |
![]() ![]() |
![]() |
#70 | ||
BOSS 5.4L Enthusiast
Join Date: Aug 2005
Posts: 21,904
|
I live in Traralgon and have Grandparents in Montrose so not that far from your shop.
It would be great if you could do a build thread of a Falcon getting a fit up, I talked to my local suspension shop (Fulcrum/Tein dealer) about you guys but he had little to no information and there isn't a lot of detail to talk to him about from what's on the website. |
||
![]() |
![]() ![]() |
![]() |
#71 | ||
Regular Member
Join Date: Jan 2013
Posts: 304
|
Thanks FPVU8,
Must be the air in China but I forgot about Nispro and Herrod so I hope they are not reading haha. In the middle of a huge subjective evaluation report so the brain is a bit dead. About 40 different things to rate on the ride and handling ![]() Next time we are installing a set of Ford dampers, I will give you a call through the forum and you are more than welcome to see how we install our damper kit. we have sold many sets but only one to a forum member direct and installed for him so hope to get some more business from the guys in the threads. Thanks and look forward to meeting you one day. Cheers Brett |
||
![]() |
![]() ![]() |
This user likes this post: |
![]() |
#72 | |||
AWD Assassin
Join Date: Dec 2004
Posts: 8,170
|
Quote:
Again - depends on what you want in the car and how prepared you are to put up with a little bit of rough and tumble when the roads are bad - but this set up is very close to the factory feel in terms of damping. PM me if you wanna talk more. |
|||
![]() |
![]() ![]() |
2 users like this post: |
![]() |
#73 | ||
BOSS 5.4L Enthusiast
Join Date: Aug 2005
Posts: 21,904
|
Thanks for the response Brett, looking forward to seeing some more feedback on these kits.
|
||
![]() |
![]() ![]() |
This user likes this post: |
![]() |
#74 | |||
Join Date: Jul 2005
Location: Perth, Western Australia
Posts: 4,513
|
Quote:
.
__________________
2015 FGX XR8 5.0 S/C 645 RWKW ![]() |
|||
![]() |
![]() ![]() |
3 users like this post: |
![]() |
#75 | |||
Call me dirt... Joe Dirt
Join Date: May 2009
Location: Back in Perth for good
Posts: 5,302
|
Quote:
Cheers.
__________________
2007 BFII FPV Cobra Ute|Boss 302|6M|#23/100 Mods so far: Billet Products Shifter|X-Force Exhaust|Herrod Oil Breathers|Whiteline Sway Bar|Tein SuperStreets|Kings FOR-303SL Rear Springs|Melling Oil Pump|Mace Manifold Spacers|Powerbond Underdrives|Pacemaker Headers|Ballistic Cats|XFT Custom Tune @ 308.3rwkw|DBA T3 Rotors|Ferodo Pads|Goodridge Braided Lines Mods to come: 4.11 Diff Gears|Chromoly Tailshaft I use & recommend: Castrol|Motorcraft|Mainlube|Penrite Check Out My Build Thread |
|||
![]() |
![]() ![]() |
![]() |
#76 | |||
Member
Join Date: Mar 2005
Location: Hobart, Tasmania
Posts: 1,991
|
Quote:
I wonder which will be more suitable for other brands of leaf springs (i.e. not genuine Ford or Herrods), such as King Springs, then?
__________________
Current vehicles: MY12 Land Rover Discovery 4 TDV6, MY03 Land Rover Discovery 2 HSE Td5 off road modified and 1989 Mazda NA MX-5 toy car. Previously: 1992 Ford EBII Fairmont, 1994 Ford EF Falcon XR6 supercharged, 2003 Ford BA Falcon XR6 Turbo 325rwkw, and 2002 Ford AU3 Falcon XR8 Pursuit 250 270rwkw. |
|||
![]() |
![]() ![]() |
![]() |
#77 | ||
Whining
Join Date: Mar 2012
Location: Perth
Posts: 384
|
These look/sound like the ducks nuts. Willing to buy my pedders coilovers and put in a set of these?
(haha) |
||
![]() |
![]() ![]() |
![]() |
#78 | |||
Regular Member
Join Date: Jan 2013
Posts: 304
|
Quote:
I am sure in the near future we will get a ute with the King springs to see how the dampers perform and if we need to do any retuning, it's not an issue and easy for us to do. Our dampers are so tunable that we can cater for any different rate that Kings or any other aftermarket leafs may have and just revalve before we supply. We can easily change the adjustment range as well to suit the body control so no problem at all. Just need to get through the range of leafs available. Cheers |
|||
![]() |
![]() ![]() |
![]() |
#79 | |||
Member
Join Date: Mar 2005
Location: Hobart, Tasmania
Posts: 1,991
|
My new Shockworks coilovers for the front of the ute just arrived at work. Thanks to Brett and Chris to arranging the supply!
It is currently 3.5*C outside (with a "feels like" rating of 0*C) - despite this if all goes to plan I'll be in the driveway tonight installing these! With regards to the matching rear units: Quote:
At present I find that my ute rides a lot nicer on the street when there is a bit of a load in the tray. At present I have installed King Spring FOR-304 leaf springs (http://www.kingsprings.com/catalogue..._catalogue.pdf - these like Herrods leaf springs are the Reverse Eye Type Design to "...reduce ride height without reducing ride comfort" < http://www.herrodmotorsport.com.au/H...4/Default.aspx >) and I also have the Mal Wood Ford Ute Tramp Rod Kit Installed ( http://www.malwoodauto.com.au/index....=tramp_rod_kit ) with the Bilstein shock absorbers in the rear. I am certainly interested in the future of purchasing the rears shock absorbers to match my newly purchased front coil overs. However, my current shock absorbers in the rear are Bilsteins which I always believed to be the ducks nuts (or at least as close as you can get without full custom jobbies). I suppose my question therefore, is what benefits/advantages or changes could I notice in replacing my Bilsteins with the Shockworks units?
__________________
Current vehicles: MY12 Land Rover Discovery 4 TDV6, MY03 Land Rover Discovery 2 HSE Td5 off road modified and 1989 Mazda NA MX-5 toy car. Previously: 1992 Ford EBII Fairmont, 1994 Ford EF Falcon XR6 supercharged, 2003 Ford BA Falcon XR6 Turbo 325rwkw, and 2002 Ford AU3 Falcon XR8 Pursuit 250 270rwkw. |
|||
![]() |
![]() ![]() |
![]() |
#80 | ||
Member
Join Date: Mar 2005
Location: Hobart, Tasmania
Posts: 1,991
|
I thought since pictures are a bit sparse in this thread I would throw a few up that I took when unboxing my front coil overs.
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
__________________
Current vehicles: MY12 Land Rover Discovery 4 TDV6, MY03 Land Rover Discovery 2 HSE Td5 off road modified and 1989 Mazda NA MX-5 toy car. Previously: 1992 Ford EBII Fairmont, 1994 Ford EF Falcon XR6 supercharged, 2003 Ford BA Falcon XR6 Turbo 325rwkw, and 2002 Ford AU3 Falcon XR8 Pursuit 250 270rwkw. |
||
![]() |
![]() ![]() |
![]() |
#81 | ||
AWD Assassin
Join Date: Dec 2004
Posts: 8,170
|
^^^
They look exactly like mine.....lol They are nice well made unit. Had my set in the GT for a while. Nothing but positive things too say at this stage. Very happy. |
||
![]() |
![]() ![]() |
![]() |
#82 | ||
Sneaky
Join Date: Feb 2013
Location: Little Old Adelaide
Posts: 985
|
They do look great as far as sruts go.
![]() Am i to assume that coilovers are legal on road cars? Just thought i'd ask as my brother in-law has got cold feet in regards to fitting them to his VZ Dunnydore so he can put 40series tyres on his 19's. |
||
![]() |
![]() ![]() |
![]() |
#83 | ||
Smash the Boost
Join Date: Jan 2005
Location: Brisbane
Posts: 2,692
|
I did read in new Codes of Practise adopted recently in QLD they did mention coilovers are now illegal.
Not exactly sure as yet what that means (if a authorised person can engineer it or not) but I intend to find out. Tax time means new shocks. Sent from my GT-P7510 using Tapatalk HD
__________________
2023 Hyundai Palisade 1971 Fairmont Sedan 1974 SWB F100 Keyboard Warrior - A Person who, being unable to express his anger through physical violence (owning to their physical weakness, lack of bravery and/or conviction in real life), instead manifests said emotions through the text-based medium of the internet, usually in the form of aggressive writing that the Keyboard Warrior would not (for reasons previously mentioned) be able to give form to in real life.
|
||
![]() |
![]() ![]() |
![]() |
#84 | ||||
Member
Join Date: Mar 2005
Location: Hobart, Tasmania
Posts: 1,991
|
I poked around yesterday on the shock and I can feel the bump stop there underneath the dust boot cover.
Quote:
Quote:
I did however, find this on the Queensland Department of Transport and Main Roads' website < http://www.tmr.qld.gov.au/Safety/Veh...fications.aspx > which indicates that Queensland now follow the National Code of Practice (NCOP) for Light Vehicle Construction and Modification - see my next paragraph for this documents relevancy. I believe all States are now following the National Code of Practice (NCOP) for Light Vehicle Construction and Modification Vehicle Standards Bulletin (VSB) 14 ( http://www.infrastructure.gov.au/roa.../vsb_ncop.aspx ) In this case is it probably NCOP11 Section LS Suspension and Steering V2 01Jan2011 that is most relevant. Section 1.1 titled '1.1 BASIC MODIFICATIONS NOT REQUIRING CERTIFICATION' describes the "...following modifications may be performed without certification if they are carried out in accordance with sub-section 2 General Requirements and the total change in vehicle height resulting from all modifications performed, does not exceed 50mm." (p. 6): Shock absorber substitution; Spring and sway bar substitution Also of note is 1.2 MODIFICATIONS REQUIRING CERTIFICATION UNDER SECTION LS (p. 6) and 1.3 MODIFICATIONS NOT COVERED UNDER SECTION LS (pp. 6 - 7), however, coilovers aren't specifically listed in either of these, so we can continue (if the vehicle has ESC however, then this document doesn't strictly apply as ESC vehicles are a whole different bag of tricks apparently): Reference then to sub-section 2 General Requirements (pp. 7 to 17) which covers the topics of Driveability, Strength and Flexibility, Fabrication, Steering and Suspension Terminology, Relevant Publications, Modifications to Vehicles Equipped with ESC, Safety Issues Associated with Raising or Lowering a Vehicle - skimming through these I don't see anything relating to coilovers. The easiest way to find out if they are legal in your state is to just phone or e-mail the road transport agency's technical department. I have done this a few times here in Tasmania for information. Considering the standard setup in the front of the Falcons is a coil over the strut I would assume at least for the front of a Falcon the coilovers are legal as the only difference is the spring base can now be adjusted for height purposes. I would also be suprised if large National chains like Fulcrum Suspension (retailer of Tein) and Pedders would be selling coilovers if they were illegal. The legal ramifications to them would be too great in regards to their duty of care. There's so many myths and BS floating around on online forums with no references to back them up. Find the source of the rules and read them and usually that will provide you with at least 90% of your answer.
__________________
Current vehicles: MY12 Land Rover Discovery 4 TDV6, MY03 Land Rover Discovery 2 HSE Td5 off road modified and 1989 Mazda NA MX-5 toy car. Previously: 1992 Ford EBII Fairmont, 1994 Ford EF Falcon XR6 supercharged, 2003 Ford BA Falcon XR6 Turbo 325rwkw, and 2002 Ford AU3 Falcon XR8 Pursuit 250 270rwkw. Last edited by twr7cx; 27-06-2013 at 10:57 AM. |
||||
![]() |
![]() ![]() |
![]() |
#85 | ||
BEN
Join Date: Jun 2011
Location: Perth WA
Posts: 4,875
|
Illegal in WA unless engineered.
__________________
My Thread. The new whip: 2014 FGX XR8 Auto in victory gold. Mods : BMC air filter, 1500cc injectors, Walbro 485, 58mm kpm snout, kpm intercooler, 35% front and 20% rear tint, pedders supercar coilovers, whiteline sway bars, Phillips HIDs, lenso d1r wheels. 331rwkw. 12.7 sec stock as a rock with a passenger. Now with 620rwhp ready to run the 10 built zf, built tailshaft, corn juice all to come. The old rig: 2008 FG XR8 Auto in dash green with a tonne of mods to make 311rwkw. |
||
![]() |
![]() ![]() |
![]() |
#86 | ||
Member
Join Date: Mar 2005
Location: Hobart, Tasmania
Posts: 1,991
|
Got any more details on that such as a reference? As I note that WA also has adopted the NCOP ( http://www.transport.wa.gov.au/media...htVehicles.pdf ).
__________________
Current vehicles: MY12 Land Rover Discovery 4 TDV6, MY03 Land Rover Discovery 2 HSE Td5 off road modified and 1989 Mazda NA MX-5 toy car. Previously: 1992 Ford EBII Fairmont, 1994 Ford EF Falcon XR6 supercharged, 2003 Ford BA Falcon XR6 Turbo 325rwkw, and 2002 Ford AU3 Falcon XR8 Pursuit 250 270rwkw. |
||
![]() |
![]() ![]() |
![]() |
#87 | |||
BEN
Join Date: Jun 2011
Location: Perth WA
Posts: 4,875
|
Quote:
__________________
My Thread. The new whip: 2014 FGX XR8 Auto in victory gold. Mods : BMC air filter, 1500cc injectors, Walbro 485, 58mm kpm snout, kpm intercooler, 35% front and 20% rear tint, pedders supercar coilovers, whiteline sway bars, Phillips HIDs, lenso d1r wheels. 331rwkw. 12.7 sec stock as a rock with a passenger. Now with 620rwhp ready to run the 10 built zf, built tailshaft, corn juice all to come. The old rig: 2008 FG XR8 Auto in dash green with a tonne of mods to make 311rwkw. |
|||
![]() |
![]() ![]() |
![]() |
#88 | ||
AWD Assassin
Join Date: Dec 2004
Posts: 8,170
|
Not illegal in Victoria
Section 13.2 VSB 14 lists that you can substitute suspension components without certification - provided amongst other things it is not raised or lowered by more than 1/3 of its initial suspension travel. No mention of coilovers as exclusions. Cars with ESC may be different - as lowering or raising may affect the way the ECU responds to its set programming ? This is more to do with parameter alterations than hardware change - so it would apply to lowering / raising the vehicle regardless of coilovers or using lowering springs. This doesnt stop the boys in BLUE questioning anything they want to question - just means you are obliged to prove what you have modified is within the rules legislated by your state. |
||
![]() |
![]() ![]() |
This user likes this post: |
![]() |
#89 | ||
Regular Member
Join Date: Jan 2013
Posts: 304
|
Hi Guy's,
I have been going over the regulations, and from what I see we comply with all of the reg's under the vehicle standards rules. With the Ford we have retain all the of the Factory rod travel and just a little shorter in the rear by about 12mm from memory but fall way inside the 2/3rd's rule for travel. We have also extensively tested the car's performance with the stability system with no reduced effects on performance. Section 4.4 outlines compatible mountings which we have the same dimensions as factory but the Ford lower clevis bracket for BA-BF is 2.5mm thickness and our brackets are 5mm thickness to make sure we have super strong mountings. From what I see we are all good but will keep going over as now I am interested to read this material. Cheers |
||
![]() |
![]() ![]() |
3 users like this post: |
![]() |
#90 | |||
AWD Assassin
Join Date: Dec 2004
Posts: 8,170
|
Quote:
The only difference with the shockworks stuff / pedders / tein etc is that they are "adjustable". In fact the Tein with the EDFC may be an issue as it has the potential to be "manually" adjusted whilst driving ?? Not sure on the technicality of that. The rear units are a separate shock and spring - like the factory units as well - so there is no modification per se.....its more in line with the substitution rule. Now adding a complete coiolver kit to an XE falcon may be an issue as the body of the vehicle may need to be modified to suit. This is an interesting area and probably comes down to interpretation of the regs. I'm sure there would be roadworthy testing centres out there in all states that would not pass on these sorts of mods out of pure confusion and caution. Then again - there would be plenty that would based on the substitution ruling. |
|||
![]() |
![]() ![]() |