|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
25-12-2018, 10:25 PM
|
#1 | ||
|
Starter Motor
Join Date: Jun 2016
Posts: 1
|
Engine no start - Checked fuel pump operation & pressure, all good & holds. Tried to retrieve codes from diagnostic connector in engine bay by earthing out & LED test lamp, but none make sense. Further checks found no injector impulse signal & there seems to be no spark also. (Common cause in case is Crank Angle sensor (Was replaced - No Diff). I don't think/believe the vehicle is fitted an engine immobiliser, as there is dash lamp display. Removed instrument cluster & checked if lamp was fitted & no provision for same.
Any Ideas Out There Would Be Appreciated |
||
|
|
|
26-12-2018, 03:58 AM
|
#2 | ||
|
FF.Com.Au Hardcore
Join Date: Jun 2010
Location: Perth
Posts: 1,315
|
Ford Laser = prior to 1994.
What do you mean by 2009 ? Obviously unless you can do the diagnose yourself, it will cost more to fix than the car is worth. If you have a repair manual and a basic multimeter you need to check every signal / wire loop all the way back to the ECU. By law in some states, there should have been an immobilizer. Cheers, |
||
|
|
|
|
26-12-2018, 11:24 AM
|
#3 | ||
|
FF.Com.Au Hardcore
Join Date: Mar 2013
Posts: 7,680
 
|
Last Laser was the KQ and finished in 2002. So the vehicle cranks but no start? Have you checked power to the coil pack?
|
||
|
|
|
|
26-12-2018, 01:09 PM
|
#4 | |||
|
Experienced Member
Join Date: Sep 2006
Location: Australasia
Posts: 7,658
|
Quote:
All KN & KQ laser models were equipped with immobilisers. |
|||
|
|
| This user likes this post: |
|
26-12-2018, 01:53 PM
|
#5 | ||
|
Experienced Member
Join Date: Sep 2006
Location: Australasia
Posts: 7,658
|
Check IAC valve, ignition coils, ignition timing, spark plugs, high tension leads, crank shaft sensor or pulley damaged also improper gap setting. EGR system malfunction.
You will need to use a jumper wire in conjunction with multitester or test light, you will also need the diagnostic chart to read the pulse signals. You will find the repair manual if you google for it. |
||
|
|
|
|
26-12-2018, 03:38 PM
|
#6 | ||
|
Shenanigans..............
Join Date: Mar 2007
Location: Footscrazy
Posts: 12,479
|
No spark, no injectors. Sounds like a classic case of immobilisaton.
A normal key won't start it, and if memory is correct, you will be locked out of system even with the correct key. (I think that system is a 3 strikes and you're out). Easiest way is to ring around locksmiths who know of this system and go from there. |
||
|
|
|
Laser 08/2009 KN Auto Sedan-1.6 ZM Eng
Linear Mode
