|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
24-02-2019, 11:37 AM
|
#1 | ||
|
DIY Tragic
Join Date: Apr 2018
Location: Sydney, more than not. I hate it.
Posts: 22,354
|
I’ve been having a crack. Made a bracket of punched strapping because I had some handy. Reinforced the pops with SS flatwashers and backed the bracket with D-Mastic.
  
|
||
|
|
| This user likes this post: |
|
24-02-2019, 12:53 PM
|
#2 | ||
|
FF.Com.Au Hardcore
Join Date: Mar 2005
Posts: 1,218
|
Looks good but the only caution would be the fan flow may be less because of the added restriction of the filter which was not factored in the original design.
Hopefully it works so let us know how it goes. Bill.
__________________
AUII XR6 VCT ute 20 years and still going strong! |
||
|
|
|
24-02-2019, 01:04 PM
|
#3 | ||
|
DIY Tragic
Join Date: Apr 2018
Location: Sydney, more than not. I hate it.
Posts: 22,354
|
Yes, I do expect it to load the motor up more. Cautiously optimistic, though.
|
||
|
|
|
|
01-04-2019, 01:09 PM
|
#4 | ||
|
Afterburner + skids =
 
Join Date: Dec 2004
Location: Skidsville
Posts: 12,128
|
How'd you go with this mate?
__________________
Speed Kills. So buy an AU XR8 and live forever. Oo\===/oO |
||
|
|
|
|
01-04-2019, 07:39 PM
|
#5 | ||
|
DIY Tragic
Join Date: Apr 2018
Location: Sydney, more than not. I hate it.
Posts: 22,354
|
G'day, it's in the mongrel ute which is still off the road with my immobilisation issue.
Have run the fan on all speeds, seems no increase in working noise or vibration, no odd hot smells or blown fuses. Can't really comment on before/after airflow as the old HVAC box foam seals were history when I started. The final test - which I'll try tomorrow once done soldering in a bypass connector for the ECU harness - is filter R&R. It's pretty cosy! |
||
|
|
|
| This user likes this post: |
|
03-04-2019, 08:09 PM
|
#6 | ||
|
DIY Tragic
Join Date: Apr 2018
Location: Sydney, more than not. I hate it.
Posts: 22,354
|
It's tight as the proverbial analogy of your choosing. :-/
To get the filter out/in you need to disconnect, unclip and shove aside the vacuum connector block and the HVAC harness connector block. And the ECU-dash harness connector block. That's presuming glovebox already out. Normally these aspects wouldn't faze me but the matter of Ford using thin ABS for the connector mount tabs, is the "hmmm" part. I think the height of the filter is the greatest issue here, were it (say) 20mm tall instead of 30, the job would be a lot less hassle - but the tradeoff is losing 1/3 your filter area at the same pleat spacing. No regrets about doing it, seems nil practical effect on the cabin ventilation, but I might explore other filters were I making it again. The other tweak is to allow a bit more room within the holding clips to slide the filter left/right/up/down (maybe 5×5mm extra) just to help the sealing foam "flick" out where it gets folded over accidentally in fitting. |
||
|
|
|
| This user likes this post: |
|
04-04-2019, 03:11 PM
|
#7 | ||
|
Afterburner + skids =
Join Date: Dec 2004
Location: Skidsville
Posts: 12,128
|
Thanks for the update!
__________________
Speed Kills. So buy an AU XR8 and live forever. Oo\===/oO |
||
|
|
|
Fitting AU with a Pollen Filter
Linear Mode
