|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
13-10-2010, 08:51 PM
|
#1 | ||
|
Regular Member
Join Date: Sep 2010
Location: Toongabbie
Posts: 60
|
Just thought i would share this .My Au series 1 aircon used to work and the the light would go out and would blow hot air it was the standard aircon not climate control.Found out cct board was damaged the solder on the on/off switch was cracked so i resoldered them and it is as good as new $8 for the solder was alot cheaper than the $300 ford wanted for a reco cct board
|
||
|
|
|
13-10-2010, 08:56 PM
|
#2 | ||
|
FF.Com.Au Hardcore
Join Date: Apr 2009
Location: jimboomba
Posts: 4,638
|
Thanks for that mate, my buttons are actually doing the same thing, i press normal aircon mode and it keeps switching off, have to use the max aircon button
__________________
Welder/Fabricator at Beaudesert Exhuast Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors |
||
|
|
|
|
13-10-2010, 09:25 PM
|
#3 | ||
|
Regular Member
Join Date: Sep 2010
Location: Toongabbie
Posts: 60
|
thats the fault . what happens is the switch is mounted to the cct board and flexes when you press the button and eventually cracks the solder .Let me know how you go fixing it or if you want any advice.
|
||
|
|
|
|
13-10-2010, 09:27 PM
|
#4 | ||
|
FF.Com.Au Hardcore
Join Date: Apr 2009
Location: jimboomba
Posts: 4,638
|
you wouldnt to happen to no where the locating bolts are to take the facisa off,
__________________
Welder/Fabricator at Beaudesert Exhuast Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors |
||
|
|
|
|
14-10-2010, 09:36 AM
|
#5 | ||
|
gone fishing
Join Date: Jul 2006
Location: Morayfield qld
Posts: 286
|
use this thread to get the centre fascia panel off http://www.fordforums.com.au/showthread.php?t=95787
then take off the air con vent and then there are 5 or 6 screws holding the air con control pop of the back of the unit and then there are 2 small screws holing it down. once the screws are off you can see the circuit board. don't forget to prise the knobs of lol. I had a similar problem ended up getting another one from the wreckers (ftg) but had to take that to an auto elec to fix. hope it all goes good for you
__________________
Cheers Whiskers |
||
|
|
|
|
14-10-2010, 10:22 AM
|
#6 | ||
|
FF.Com.Au Hardcore
Join Date: Apr 2009
Location: jimboomba
Posts: 4,638
|
very helpfull thread, cheers
__________________
Welder/Fabricator at Beaudesert Exhuast Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors |
||
|
|
|
Au aircon switching off fixed
Linear Mode
