|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-05-2012, 09:54 PM
|
#1 | ||
Join Date: Dec 2004
Posts: 9,292
|
I remember back in 01 when i had a 2000 AU Series 1 Forte that i wanted the dash clock put in (where the FALCON badge is).
Had it booked in to Ford, only to be told that it cant be done. So, 11 years later, can it be done? Is it just as simple as putting the clock in, adding the clock loom and plugging it into a plug that is already there for it? Or is there no plug in the low series (XL Ute in this case). |
||
|
|
|
03-05-2012, 09:36 AM
|
#2 | ||
|
Flairs - Truckers Delight
Join Date: Aug 2006
Location: Brisbane Northside Likes: Opposite Lock
Posts: 5,731
|
yes it can be done
do a search, there's a thread where someone did it
__________________
Current: Silhouette Black 2007 SY Ford Territory TX RWD 7-seater "Black Banger"
2006-2016: Regency Red 2000 AUII Ford Falcon Forte Automatic Sedan Tickford LPG "Millennium Falcon" |
||
|
|
|
|
03-05-2012, 09:45 AM
|
#3 | ||
|
FF.Com.Au Hardcore
Join Date: Aug 2006
Location: Salamander Bay
Posts: 5,427
|
I'm fairly sure the plug is there just fit the clock and plug it in
__________________
[SIGPIC][/SIGPIC]
Everyone starts off with a bag full of luck and an empty bag of experience. The trick is to fill the experience bag before the luck bag is empty. "It is better to remain silent and be thought a fool than to speak out and remove all doubt." Start a new career as a bus driver Rides: FG2 XR6 stock at this stage but a very nice ride xc 4 DOOR X CHASER 5.8 UNDER RESTO |
||
|
|
|
|
04-05-2012, 09:02 PM
|
#4 | ||
|
Join Date: Dec 2004
Posts: 9,292
|
Well, from the results i have found here, it seems the general consensus is that it doesnt have the require plug in the dash and it cant be done without wiring it from scratch.
Would love to be proved wrong though.............. |
||
|
|
|
|
23-05-2012, 09:26 PM
|
#5 | ||
|
Join Date: Dec 2004
Posts: 9,292
|
So after having a good look around inside the dash, i couldnt see anywhere to plug in a clock.
|
||
|
|
|
|
30-05-2012, 09:39 AM
|
#6 | ||
|
Evil Mastermind
Join Date: May 2012
Location: Lake Illawarra
Posts: 91
|
Even with no plug, wiring it in should not be a difficult process. You would need an earth connected to the body, a feed from the battery side of the ignition (to keep the clock permanently on) and a feed from the light switch so when the lights are on the clock's backlight is on.
|
||
|
|
|
|
30-05-2012, 09:54 AM
|
#7 | ||
|
HUGE MEMBER
Join Date: May 2012
Location: Brissy Bayside
Posts: 716
|
Take the blank panel off and have a look for a plug. I was told I couldn't put a clock in my EL gli. I was a bit sceptic,thinking ford would not make a whole lot of looms. I pulled the falcon blank panel off and the plug was just sitting there. I pluged it in pushed.the clock into the whole and I now have a working clock. Hopefully it is the same for your Au
Sorry just saw the post, two above this one
__________________
I would not pee on a Holden if it were on fire. I would take pics and post for your pleasure My cruiser. 1979 Zh Marquis. "T" code 351. My garage queen :(. 1980 TF Cortina Ghia Wagon. 4.1. My dog. 2011 Sierra My Daily. 2012 ZH (lol) OUTLANDER xls. 4WD CVT. Sapphire blue Wanted Borg Warner Lsd or centre. 25 spline |
||
|
|
|
|
30-05-2012, 07:59 PM
|
#8 | ||
|
Lost Boost Gained Class
Join Date: Jun 2008
Location: Werribee, Melbourne
Posts: 2,763
|
had a 98 Forte and it had the blanking off plate i pulled it off and fitted the clock as the loom was there
__________________
2006 BF Fairmont Ghia
2001 AU Falcon |
||
|
|
|
Adding dash clock to base model AU
Linear Mode
