|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
| The Pub For General Automotive Related Talk |
 |
|
|
Thread Tools | Display Modes |
23-04-2005, 11:26 AM
|
#1 | ||
|
Saving Water Filthy again
Join Date: Dec 2004
Location: somewhere between sedate and hectic
Posts: 500
|
Tomorrow I will be using the GT-P as a wedding car. I was wondering if anyone knew of a way to prevent the ribbon from creating a rub mark on the grill surround or the bonnet.
I was thinking of getting some white flannelette between the ribbon and the paintwork, but any other ideas would be appreciated. Regards Steven
__________________
Blood Orange BA FPV GT-P. Again, now I am complete Last edited by Filthy GT-P; 23-04-2005 at 11:27 AM. Reason: spelling |
||
|
|
|
23-04-2005, 11:42 AM
|
#2 | ||
|
Chairman & Administrator
  
Join Date: Dec 2004
Location: 1975
Posts: 107,522
|
The simplest way is a bit of 3M bonnet stone guard tape - I don't put the whole sheet on but have been cutting up the same sheet each time I've used it for this purpose (twice now). The sheet should last about 6 goes at this rate which is more than I'm likely to do.
Russ
__________________
 Observatio Facta Rotae
|
||
|
|
|
|
23-04-2005, 12:04 PM
|
#3 | |||
|
Saving Water Filthy again
Join Date: Dec 2004
Location: somewhere between sedate and hectic
Posts: 500
|
Quote:
It's for Matt from G & D's wedding tomorrow. To quote an annoying TV Add "Where do you get it?" Thanks Steven
__________________
Blood Orange BA FPV GT-P. Again, now I am complete |
|||
|
|
|
|
23-04-2005, 12:09 PM
|
#4 | ||
|
Chairman & Administrator
Join Date: Dec 2004
Location: 1975
Posts: 107,522
|
Most Autorice stores should carry it - ring your local one and check.
Cheers Russ
__________________
Observatio Facta Rotae
|
||
|
|
|
|
23-04-2005, 12:17 PM
|
#5 | ||
|
Saving Water Filthy again
Join Date: Dec 2004
Location: somewhere between sedate and hectic
Posts: 500
|
It's about $51.00 from my local Autobarn
I thought I would also ring supercrap didn't know what I was talking about and suggested I ring Autobarn. Steven
__________________
Blood Orange BA FPV GT-P. Again, now I am complete |
||
|
|
|
|
23-04-2005, 12:22 PM
|
#6 | ||
|
Guest
Posts: n/a
|
Easier method. I ran a HSV for two years doingw eddings every weekend.
Get some Megiuars Yellow Wax PASTE. Apply liberally to bonnet and let dry thoroughly. Apply second coat. Fit ribbon and then wipe off excess either side of the ribbon. Also, make the ribbon tight and so that when you shut the bonnet it pulls the ribbon that extra bit and preloads it. No marks. Guaranteed. And cheap. |
||
|
|
|
23-04-2005, 02:26 PM
|
#7 | ||
|
Formerly known as TS 50
Join Date: Dec 2004
Location: NEWCASTLE
Posts: 1,617
|
Use silk ribbons only. They don't mark your paint.
__________________
BLUEPRINT T3 TS50 #109, MANUAL WITH BREMBOS
|
||
|
|
|
|
23-04-2005, 02:38 PM
|
#8 | |||
|
Ford Fanatic
Join Date: Feb 2005
Location: Brisbane
Posts: 1,480
|
Quote:
This would have been my idea too
__________________
Everyone is entitled to my Opinion  2007 Territory TX SY RWD Ego |
|||
|
|
|
|
25-04-2005, 08:46 PM
|
#9 | ||
|
Guest
Posts: n/a
|
The silk ribbons are a necessity. Agreed. But the damage also occurs from dirt getting between the ribbon and the paint. the wax keeps these from scratching the paint.
|
||
|
|
|
26-04-2005, 10:40 AM
|
#10 | ||
|
Starter Motor
Join Date: Jan 2005
Posts: 24
|
best way is to bend up a piece of metal with holes in it that bolts/screws to the factory holes under the hood and pokes out forward between the grille and hood, then folds 90degrees skyward witha hole in the end to thread the ribbon through. It wont get in the way of opening/closing the hood, and you can tighten the ribbon all you like and it doesnt touch the paint at all. It sits only centimeters above the hood. Somthing to consider making if you plan on doing a few weddings. I had one for my Falcon (XY) and although its design would be different to suit the BA the basic idea is the same
|
||
|
|
|
|
26-04-2005, 07:46 PM
|
#11 | ||
|
Saving Water Filthy again
Join Date: Dec 2004
Location: somewhere between sedate and hectic
Posts: 500
|
I took Russelw's advice and it worked well. Some of the other advice is also very good, but time was very short.
The protector came off with a hair dryer and left no marks whatsoever. Thanks everyone for your help the thread with a picture of the cars is here Regards Steven
__________________
Blood Orange BA FPV GT-P. Again, now I am complete |
||
|
|
|
How can you prevent wedding Car ribbons from rubbing on the paintwork
Linear Mode
